View AXH010A0FZ_8036082.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

data sheet october 1, 2009 austin lynx tm sip non-isolated dc-dc power modules: 3.0 vdc - 5.5 vdc input, 0.9 vdc - 3.3 vdc output, 10 a document name: fds02-047eps ver.1. 6 pdf name: austin l ynx sip applications n distributed power architectures n wireless networks n access and optical network equipment n enterprise networks n data processing equipment n latest generation ic?s (dsp , fpga, asic) and micropro- cessor-powered applications. options n remote sense n long pins: 5.08 mm 0.25 mm (0.200 in 0.010 in) features n compatible with rohs eu directive 200295/ec (-z ver- sions) n compatible in rohs eu directive 200295/ec with lead solder exemption (non -z versions) n delivers up to 10a output current n high efficiency: 95% at 3.3v full load n small size and low profile: 50.8 mm x 8.10mm x 12.7mm (2.0 in x 0.32 in x 0.5 in) n light weight 0.27 oz(7.5 g) n cost-efficient open frame design n high reliability: mtbf > 10m hours at 25 c n remote on/off n output overcurrent prot ection with auto-restart n overtemperature protection n constant frequency (300 khz,typical) n adjustable output voltage 10% of vo (?5% to + 10% for 0.9 v output) n single-in-line (sip) package n ul * 60950 recognized, csa ? c22.2 no. 60950-00 certi- fied, and vde ? 0805 (iec60950, 3rd edition) licensed rohs compliant description austin lynx? power modules are non-isolated dc-dc converters t hat can deliver 10 a of output current with full load efficiency of 95% at 3.3 v output. these open frame modul es in sip package enable designers to devel op cost-and space efficient solutions. standard features include remote on/o ff, output voltage adjustment, overcu rrent and overtemperature protection. * ul is a registered trademark of underwriters laboratories, inc. ? csa is a registered trademark of canadian standards association. ? vde is a trademark of verband deutscher elektrotechniker e.v. this product is intended for integration into end-use equipment. all the required procedures for ce marking of end-use equipm ent should be followed. (the ce mark is placed on selected products.) ** iso is a registered trademark of the internation organization of standards
lineage power 2 data sheet october 1, 2009 3.0 vdc - 5.5 vdc input, 0. 9 vdc - 3.3 vdc output, 10 a austin lynx tm sip non-isolated dc-dc power modules: absolute maximum ratings stresses in excess of the absolute maximum ratings can ca use permanent damage to the dev ice. these are absolute stress ratings only, functional operation of the device is not implied at these or any other conditions in excess of those given in th e operations sections of the data sheet. exposure to absolute maximum ratings for extended periods can adversely affect the device reliabiltiy. electrical specifications unless otherwise indicated, specif ications apply over all operating input voltag e, resistive load, and temperature conditions. caution: this power module is not inte rnally fused. an input line fuse must always be used. to preserve maximum flexibility, internal fusing is not included; however, to achieve maximum safety and system protection, always use an input line fuse. the safety agenc ies require a time-delay fuse with a maximum rating of 20a. parameter device symbol min max unit input voltage: continuous all vin 0 6.5 vdc operating ambient temperature all ta ?40 85 c storage temperature all tstg ?55 125 c parameter device symbol min typ max unit operating input voltage axh010a0s0r9 axh010a0s1r0 axh010a0p axh010a0m axh010a0y axh010a0d axh010a0g axh010a0f vin vin vin vin vin vin vin vin 3.0 3.0 3.0 3.0 3.0 3.0 3.0 4.5 5.5 5.5 5.5 5.5 5.5 5.5 5.5 5.5 vdc vdc vdc vdc vdc vdc vdc vdc maximum input current (vi = 0 to vi,max; io = io,max) ii,max 9.5 a input reflected-ripple current (5 hz to 20 mhz; 1 h source impedance; ta = 25 c; cin = 200 f) 30 map-p input ripple rejection (100 - 120hz) 40 db
lineage power 3 data sheet october 1, 2009 3.0 vdc - 5.5 vdc input, 0.9 vdc - 3.3 vdc output, 10 a austin lynx tm sip non-isolated dc-dc power modules: electrical specifications (continued) general specifications parameter device symbol min typ max unit output voltage set point (vi = 5v; io = io,max; ta = 25 c) axh010a0s0r9 axh010a0s1r0 axh010a0p axh010a0m axh010a0y axh010a0d axh010a0g axh010a0f vo,set vo,set vo,set vo,set vo,set vo,set vo,set vo,set 0.886 0.985 1.182 1.47 1.764 1.97 2.45 3.234 0.9 1.0 1.2 1.5 1.8 2.0 2.5 3.3 0.914 1.015 1.218 1.53 1.836 2.03 2.55 3.366 vdc vdc vdc vdc vdc vdc vdc vdc output voltage (over all operating input voltage, resistive load, and temperature conditions at steady state until end of life.) axh010a0s0r9 axh010a0s1r0 axh010a0p axh010a0m axh010a0y axh010a0d axh010a0g axh010a0f vo vo vo vo vo vo vo vo 0.873 0.970 1.164 1.455 1.746 1.94 2.425 3.2 ? ? ? ? ? ? ? ? 0.927 1.03 1.236 1.545 1.854 2.06 2.575 3.4 vdc vdc vdc vdc vdc vdc vdc vdc output regulation: line (vi = vi, min to vi, max) load (io = io, min to io, max) temperature (ta = ta, min to ta, max) all all all ? ? ? ? ? ? 0.2 0.4 0.5 %vo , s et %vo, set %vo, set output ripple and noise measured across 10f tantalum, 1f ceramic, rms (5 hz to 20 mhz bandwidth) peak-to-peak (5 hz to 20 mhz bandwidth) all all ? ? ? ? 7 25 15 30 mvrms mvp-p output current all io ? 10 a output current-limit inception (vo = 90% of vo, set) all io 17 a output short-circuit current (average) vo = 0.25 v all io 3 a efficiency (vi = vin, nom; io = io, max), ta = 25 c axh010a0s0r9 axh010a0s1r0 axh010a0p axh010a0m axh010a0y axh010a0d axh010a0g axh010a0f 83 85 86 88 90 91 92 95 % % % % % % % % switching frequency all fsw ? 300 ? khz parameter min typ max unit calculated mtbf (io = 100% of io, max ta = 25 c) 10,240,000 hours weight ? 6.5(0.23) 7.5(0.27) g (oz.)
lineage power 4 data sheet october 1, 2009 3.0 vdc - 5.5 vdc input, 0. 9 vdc - 3.3 vdc output, 10 a austin lynx tm sip non-isolated dc-dc power modules: feature specifications unless otherwise indicated, specif ications apply over all operating input voltag e, resistive load, and temperature conditions. see feature descriptions for additional information . parameter device symbol min typ max unit remote on/off signal interface (vi = vi,min to vi, max; open collector pnp or compatible, von/off signal referenced to gnd. see figure 20 and feature descriptions section) logic low (on/off pin open?module on) ion/off = 0.0 a von/off = 0.3 v logic high (von/off > 2.5 v)?module off ion/off = 1 ma von/off = 5.5 v turn-on time (io = 80% of io, max; vo within 1% of steady state; see figure 12) all all all all all von/off ion/off von/off ion/off ? ?0.7 5 0.3 10 6.5 1 v a v ma ms output voltage set-point adjustment range (trim) axh010a0s0r9 all vtrim vtrim -5 -10 +10 +10 %vo, set %vo, set overtemperaute protection (shutdown) all tq1/tq2 ? 110 ? c input undervoltage lockout turn-on threshold turn-off threshold all all 2.63 2.47 2.8 2.7 2.95 2.9 v v
lineage power 5 data sheet october 1, 2009 3.0 vdc - 5.5 vdc input, 0.9 vdc - 3.3 vdc output, 10 a austin lynx tm sip non-isolated dc-dc power modules: characteristic cur ves the following figures provide typical characteristics curves (ta = 25 c). figure 1. input voltage and current characteristics at 10a output current. figure 2. output voltage and current characteristics. figure 3. converter efficiency vs output current axh010a0s0r9(0.9v output voltage). figure 4. converter efficiency vs output current axh010a0s1r0 (1.0v output voltage). figure 5. converter efficiency vs output current axh010a0p (1.2v output voltage). figure 6. converter efficiency vs output current axh010a0m (1.5v output voltage). 2 2.5 3 3.5 4 4.5 5 5. 5 12 10 8 6 4 2 0 i i, max = 9.5 a input voltage, v i (v) input current, i i (a) 100% 75% 50% 25% 0 0% 369 18 12 15 output current, i o (a) normalized output voltage, v o v i = 5.5 v v i = 5.0 v v i = 3.3 v v i = 3.0 v 74 76 78 80 82 84 86 88 90 1234567891 0 output current, i o (a) efficiency, (%) v i = 3.0 v v i = 3.3 v v i = 5.0 v v i = 5.5 v 74 76 78 80 82 84 86 88 90 92 v i = 3.0 v v i = 3.3 v v i = 5.0 v v i = 5.5 v output current, i o (a) efficiency, (%) 1234567891 0 output current, i o (a) efficiency, (%) 78 80 82 84 86 88 90 92 1234567891 0 v i = 3.0 v v i = 3.3 v v i = 5.0 v v i = 5.5 v output current, i o (a) efficiency, (%) 82 84 86 88 90 92 94 1234567891 0 v i = 3.0 v v i = 3.3 v v i = 5.0 v v i = 5.5 v
lineage power 6 data sheet october 1, 2009 3.0 vdc - 5.5 vdc input, 0. 9 vdc - 3.3 vdc output, 10 a austin lynx tm sip non-isolated dc-dc power modules: characteristic curves the following figures provide typical characteristics curves at room temperature (ta = 25 c) figure 7. converter efficiency vs output current axh010a0y (1.8v output voltage). figure 8. converter efficiency vs output current axh010a0d (2.0v output voltage). figure 9. converter efficiency vs output current axh010a0g (2.5v output voltage). figure 10. converter efficiency vs output current axh010a0f (3.3v output voltage). figure 11. typical output ri pple voltage at 10a output current. figure 12. typical start-up transient. 84 86 88 90 92 94 1234567891 0 output current, i o (a) efficiency, (%) v i = 3.0 v v i = 3.3 v v i = 5.0 v v i = 5.5 v 86 88 90 92 94 96 1234567891 0 output current, i o (a) efficiency, (%) v i = 3.0 v v i = 3.3 v v i = 5.0 v v i = 5.5 v 88 90 92 94 96 98 1234567891 0 output current, i o (a) efficiency, (%) v i = 3.0 v v i = 3.3 v v i = 5.0 v v i = 5.5 v 93.5 94 94.5 95 95.5 96 96.5 97 1234567891 0 output current, i o (a) efficiency, (%) v i = 4.5 v v i = 5.0 v v i = 5.5 v time, t (2 ?/div) output voltage, v o (v) (20 mv/div) v i = 3.0 v v i = 3.3 v v i = 5.0 v v i = 5.5 v time, t (2 ms/div) output voltage, v o (v) v in source
lineage power 7 data sheet october 1, 2009 3.0 vdc - 5.5 vdc input, 0.9 vdc - 3.3 vdc output, 10 a austin lynx tm sip non-isolated dc-dc power modules: characteristic curves the following figures provide typical characteristics curves at room temperature (ta = 25 c) figure 13. typical transient response to step load change at 2.5 a/s from 100% to 50% of io,max at 3.3 v input (cout =1 f ceramic, 10 f tantalum). figure 14. typical transient response to step load change at 2.5 a/s from 50% to 100% of io,max at 3.3 v input (cout =1 f ceramic, 10 f tantalum). time, t (5 ?/div) output current i o ( 2.5 a/div) output voltage v o (100 mv/div) time, t (5 ?/div) output current i o ( 2.5 a/div) output voltage v o (100 mv/div)
lineage power 8 data sheet october 1, 2009 3.0 vdc - 5.5 vdc input, 0. 9 vdc - 3.3 vdc output, 10 a austin lynx tm sip non-isolated dc-dc power modules: test configurations note: measure input reflected ripple current with a simulated source inductance (l test ) of 1h. capacitor cs offsets possible bat- tery impedance. measure current as shown above. figure 15. input reflected ripple current test setup. note: scope measurements should be made using a bnc socket, with a 10 f tantalum capacitor and a 1 f ceramic capcitor. position the load between 51 mm and 76 mm (2 in and 3 in) from the module figure 16. peak-to-peak output ripple measurement test setup. note: all voltage measurements to be taken at the module termi- nals, as shown above. if sockets are used then kelvin con- nections are required at the module terminals to avoid measurement errors due to socket contact resistance. figure 17. output voltage and efficiency test setup. design considerations input source impedance to maintain low-noise and ripple at the input voltage, it is critical to use low esr capacitors at the input to the module. 18 shows the input ripple voltage (mvp-p) for various output models using a 150 f low esr polymer capacitor (pana- sonic p/n: eefue0j151r, sanyo p/n: 6tpe150m) in parallel with 47 f ceramic capacitor (panasonic p/n: ecj- 5yb0j476m, taiyo yuden p/n: cejmk432bj476mmt). figure 19 depicts much lower input voltage ripple when input capacitance is increased to 450 f (3 x 150 f) polymer capacitors in par- allel with 94 f (2 x 47 f) ceramic capacitor. the input capacitance should be able to handle an ac ripple current of at least: figure 18. input voltage ripple for various output models, io = 10 a (c in = 150 f polymer // 47 f ceramic). figure 19. input voltage ripple for various output models, io = 10 a (c in = 3x150 f polymer // 2x47 f ceramic). to oscilloscope battery l 1 h c s 220 f esr < 0.1 @ 20 c, 100 khz v i (+) v i (?) 2 x 100f tantalum v o gnd resistive load scope 10 f copper strip tantalum 1f ceramic v i v o i i i o supply c ontact resistance contact and distribution losses load gnd v o(+) v o(-) ? [] i o v i(+) v i(-) ? [] i i ------------------------------------------------ ?? ?? 100 = i rms i out v out v in ---------- - 1 v out v in ---------- - ? = a rms 0 50 100 150 200 0.5 1 1.5 2 2.5 3 v i = 5 v v i = 3.3 v output voltage, v o (vdc) input voltage noise (mv p-p) 0 25 50 75 100 0.5 1 1.5 2 2.5 3 v i = 5 v v i = 3.3 v output voltage, v o (vdc) input voltage noise (mv p-p)
lineage power 9 data sheet october 1, 2009 3.0 vdc - 5.5 vdc input, 0.9 vdc - 3.3 vdc output, 10 a austin lynx tm sip non-isolated dc-dc power modules: design considerations (continued) input source impedance (continued) the power module should be connected to a low ac-imped- ance input source. highly inductive source impedances can affect the stability of the module. an input capacitance must be placed close to the input pins of the module, to filter ripple current and ensure module stability in the presence of induc- tive traces that supply the input voltage to the module. safety considerations for safety-agency approval of the system in which the power module is used, the power module must be installed in com- pliance with the spacing and sepa ration requirements of the end-use safety agency standard, i.e., ul 60950, csa c22.2 no. 60950-00, and vde 0805:2001-12 (iec60950, 3rd ed). for the converter output to be considered meeting the requirements of safety extra- low voltage (selv),the input must meet selv requirements. the power module has elv (extra-low voltage) outputs when all inputs are elv. the input to these units is to be provided with a maximum 20a time-delay fuse in the unearthed lead.
lineage power 10 data sheet october 1, 2009 3.0 vdc - 5.5 vdc input, 0. 9 vdc - 3.3 vdc output, 10 a austin lynx tm sip non-isolated dc-dc power modules: feature descriptions remote on/off the austin lynx? sip power modules feature an on/off pin for remote on/off operation. if not using the remote on/off pin, leave the pin open (module will be on). the on/off pin signal (von/off) is referenced to ground. to switch the module on and off using remote on/off, connect an open collector pnp transistor between the on/off pin and the vi pin (see figure 20). during a logic-low when the transistor is in the off state, the power module is on and the maximum von/off generated by the module is 0.3v. the maximum leakage current of the switch when von/off = 0.3v and vi = 5.5v (vswitch = 5.2v) is 10 a. during a logic-high when the transistor is in the active stat e, the power module is off. dur- ing this state, von/off = 2.5v to 5.5v and the maximum ion/ off = 1ma. figure 20. remote on/off implementation. output voltage set-point adjustment (trim) output voltage set-point adjus tment allows the output volt- age set point to be increased or decreased by connecting either an external resistor or a voltage source between the trim pin and either the vo pi n (decrease output voltage) or gnd pin (increase output voltage). for trim-up using an external resistor, connect rtrim-up between the trim and gnd pins (figure 21). the value of rtrim-up defined as: |dvout| is the desired output voltage set-point adjustment rbuffer (internal to the module) is defined in table 1 for vari- ous models. table 1. austin lynx? trim values note: v o, set is the typical output voltage for the unit. for example, to trim-up th e output voltage of 1.5v module (axh010a0m) by 8% to 1.62v, rtrim-up is calculated as follows: figure 21. circuit configuration to trim-up output voltage. for trim-down using an external resistor, connect rtrim- down between the trim and vout pins of the module (figure 22). the value of rtrim-down is defined as: vout is the typical set point voltage of a module |dvout| is the desired out put voltage adjustment rbuffer (internal to the module) is defined in table 3 for vari- ous models for example, to trim-down the output voltage of 2.5 v mod- ule (axh010g) by 8% to 2.3v, rtrim-down is calculated as follows: vo + v switch i on/off on/off v i gnd v on/off r trim up ? 24080 v out ------------------ r buffer ?= k v o, set r buffer 3.3 v 59 kw 2.5 v 78.7 kw 2.0 v 100 kw 1.8 v 100 kw 1.5 v 100 kw 1.2 v 59 kw 1.0 v 30.1 kw 0.9 v 5.11 kw v out 0.12 v = r buffer 100 k = r trim up ? 24080 0.12 -------------- - 100 k ?= r trim up ? 100.66 k = v o trim r trim-up r load axh010a0m gnd r trim-down v out 0 . 8 ? v out ------------------------ - 1? ?? ?? x 30100 r buffer ? = k v out 0.2 v = v out 2.5 v =
lineage power 11 data sheet october 1, 2009 3.0 vdc - 5.5 vdc input, 0.9 vdc - 3.3 vdc output, 10 a austin lynx tm sip non-isolated dc-dc power modules: feature descriptions (continued) output voltage set-point adjustment (trim) (continued) figure 22. circuit configuration to decrease output voltage. for trim-up using an external voltage source, apply a voltage from trim pin to ground using the following equation: for trim-down using an external voltage source, apply a volt- age from trim pin to ground using the following equation: vtrim-up is the external so urce voltage for trim-up vtrim-down is the external source voltage for trim-down |dvout| is the desired output voltage set-point adjustment rbuffer (internal to the module) is defined in table 3 for vari- ous models if the trim feature is not being used, leave the trim pin dis- connected. remote sense austin lynx? sip power modules offer an option for a remote sense function. when the device code description includes a suffix ?3?, pin 3 is added to the module and the remote sense is an active f eature. see the ordering infor- mation at the end of this document for more information. remote sense minimizes the effects of distribution losses by regulating the voltage at the load via the sense and gnd connections (see 23). the voltage between the sense pin and vo pin must not exceed 0.5v. although both the remote sense and trim features can each increase the output volt- age (vo), the maximum increase is not the sum of both. the maximum vo increase is the larger of either the remote sense or the trim. the amount of power delivered by the module is defined as the output voltage multiplied by the output current (vo x io). when using sense and/or trim , the output voltage of the module can increase which, if the same output current is maintained, increases the power output by the module. make sure that the maximum output power of the module remains at or below the maximum rated power. when pin 3 is present but the remote sense feature is not being used, leave sense pin disconnected. figure 23. effective circuit configuration for remote sense operation. overcurrent protection to provide protection in a faul t condition, the unit is equipped with internal overcurrent protection. the unit operates nor- mally once the fault condition is removed. the power module will supply up to 170% of rated current for less than 1.25 seconds befor e it enters thermal shutdown. overtemperature protection to provide additional protection in a fault condition, the unit is equipped with a nonlatched thermal shutdown circuit. the shutdown circuit engages when q1 or q2 (shown in figure 24) exceeds approximately 110 c. the unit attempts to restart when q1 or q2 cool down and cycles on and off while the fault condition exists. recovery from shutdown is accom- plished when the cause of the overtemperature condition is removed. r buffer 78.7 k = r trim down ? 2.5 0.8 ? 0.2 -------------------- - 1? ?? ?? x 30100 78700? = r trim down ? 147.05 k = v o trim r trim-down r load gnd v trim-up 0.8 v out x r buffer 30100 ----------------- - ?= v trim-down 0.8 v out x r buffer 30100 ----------------- - += v i v o load gnd distribution losses distribution losses sense
lineage power 12 data sheet october 1, 2009 3.0 vdc - 5.5 vdc input, 0. 9 vdc - 3.3 vdc output, 10 a austin lynx tm sip non-isolated dc-dc power modules: thermal considerations the power module operates in a variety of thermal environ- ments; however, sufficient cooling should be provided to help ensure reliable operation of the unit. heat is removed by conduction, convection, and radiation to the surrounding environment. the thermal data presented is based on measurements taken in a wind tunnel. the test setup shown in figure 25 was used to collect data for figures 26 and 27. note that the airflow is parallel to the long axis of the module as shown in figure 24 and derating applies accord- ingly. figure 24. temperature measurement location . the temperature at either location should not exceed 110 c. the output power of the module should not exceed the rated power for the module (vo, set x io, max). figure 25. thermal test setup. convection requirements for cooling to predict the approximate cooling needed for the module, refer to the power derating curves in figures 26 and 27. these derating curves are appr oximations of the ambient temperatures and airflows required to keep the power mod- ule temperature below its maximum rating. once the module is assembled in the actual syst em, the module?s temperature should be checked as shown in figure 24 to ensure it does not exceed 110 c. proper cooling can be verified by measuring the power mod- ule?s temperature at q1-pin 6 and q2-pin 6 as shown in fig- ure 24. figure 26. typical power derating vs output current for 3.3 vin. figure 27. typical power derating vs output current for 5.0 vin. pin 6 q2 q1 airflow air flow x power module w ind tunnel pwbs 12.7 (0.50) 76.2 (3.0) probe locatio n for measuring airflow and ambient temperature 25.4 (1.0) 0 1 2 3 4 5 6 7 8 9 10 11 20 30 40 50 60 70 80 9 0 local ambient temperature, t a (?c) output current i o (a) 2.0 m/s (400 ft./min.) 1.0 m/s (200 ft./min.) 0.5 m/s (100 ft./min.) natural convection 0 1 2 3 4 5 6 7 8 9 10 11 20 30 40 50 60 70 80 9 0 local ambient temperature, t a (?c) output current i o (a) 2.0 m/s (400 ft./min.) 1.0 m/s (200 ft./min.) 0.5 m/s (100 ft./min.) natural convection
lineage power 13 data sheet october 1, 2009 3.0 vdc - 5.5 vdc input, 0. 9 vdc - 3.3 vdc output, 10 a austin lynx tm sip non-isolated dc-dc power modules: through-hole lead-free soldering infor- mation the rohs-compliant through-hole products use the sac (sn/ag/cu) pb-free solder and rohs-compliant components. they are designed to be processed through single or dual wave soldering machines. the pins have an rohs-compli- ant finish that is compatible with both pb and pb-free wave soldering processes. a maximum preheat rate of 3c/s is suggested. the wave preheat process should be such that the temperature of the power module board is kept below 210c. for pb solder, the recommended pot temperature is 260c, while the pb-free solder pot is 270c max. not all rohs-compliant through-hole products can be processed with paste-through-hole pb or pb-free reflow process. if addi- tional information is needed, please consult with your tyco electronics power system representative for more details. post solder cleaning and drying considerations post solder cleaning is usually the final circuit-board assembly process prior to electr ical board testing. the result of inadequate cleaning and drying can affect both the reliability of a power module and the testability of the finished circuit-board assembly. for guidance on appropriate soldering, cleaning and drying procedures, refer to tyco electronics board mounted power modules: soldering and cleaning application note (ap01-056eps). solder ball and cleanliness requirements the open frame (no case or potting) power module will meet the solder ball requirements per j-std-001b. these require- ments state that solder balls mu st neither be loose nor violate the power module minimum electrical spacing. the cleanliness designator of the open frame power module is c00 (per j specification).
lineage power 14 data sheet october 1, 2009 3.0 vdc - 5.5 vdc input, 0. 9 vdc - 3.3 vdc output, 10 a austin lynx tm sip non-isolated dc-dc power modules: outline diagram for through-hole module dimensions are in millimeters and (inches). tolerances: x.x mm 0.5 mm (x.xx in. 0.02 in.) [unless otherwise indicated] x.xx mm 0.25 mm (x.xxx in. 0.010 in.)
document no: fds02-047eps ver.1. 6 pdf name: austin lynx sip data sheet october 1, 2009 3.0 vdc - 5.5 vdc input, 0. 9 vdc - 3.3 vdc output, 10 a austin lynx tm sip non-isolated dc-dc power modules: world wide headquarters lin eag e po wer co rp or atio n 601 shiloh road, plano, tx75074 , usa +1-800-526 -7819 (outside u.s.a.: +1- 97 2-2 44-9428 ) www. l ine ag ep ower .co m e-m ail: techsupport1@linea gepower.com asia-pacific headquart ers tel: +65 6 41 6 4283 eu ro pe, m id dl e-east an d afr ic a he ad qu ar ter s tel: +49 898 780 672 80 india headquarters tel: +91 8 0 28411633 lineage power reserves the right to make changes to the product(s) or information contained herein without notice. no liability is assumed as a result of their use or application. no rights under any patent accompany the sale of any such product(s) or information. lineage power dc-dc products are protected under various patents. information on these patents is available at www.lineagepower.com/patents ? 200 9 lineage power corporation, (plano , texas) all international rights reserved. ordering information please contact your lineage power sales representa tive for pricing, availability and optional features. optional features can be ordered using the suffixes shown below. the suffixes follow the last letter of the product code and ar e placed in descending alphanumerical order. table 2. device options input voltage output voltage output current efficiency connector type device code comcodes 3.0 - 5.5 vdc 0.9 v 10 a 83% through-hole axh010a0s0r9 108966250 3.0 - 5.5 vdc 1.0 v 10 a 85% through-hole axh010a0s1r0 108966185 3.0 - 5.5 vdc 1.2 v 10 a 86% through-hole axh010a0p 108966235 3.0 - 5.5 vdc 1.5 v 10 a 88% through-hole axh010a0m 108966227 3.0 - 5.5 vdc 1.8 v 10 a 90% through-hole axh010a0y 108966243 3.0 - 5.5 vdc 2.0 v 10 a 91% through-hole axh010a0d 108966193 3.0 - 5.5 vdc 2.5 v 10 a 92% through-hole axh010a0g 108966219 4.5 - 5.5 vdc 3.3 v 10 a 95% through-hole axh010a0f 108966201 3.0 - 5.5 vdc 1.2 v 10 a 86% through-hole axh010a0pz cc109106952 3.0 - 5.5 vdc 1.5 v 10 a 88% through-hole axh010a0mz cc109106936 3.0 - 5.5 vdc 1.8 v 10 a 90% through-hole axh010a0yz cc109101788 3.0 - 5.5 vdc 2.0 v 10 a 91% through-hole axh010a0dz cc109106845 3.0 - 5.5 vdc 2.5 v 10 a 92% through-hole axh010a0gz cc109101771 4.5 - 5.5 vdc 3.3 v 10 a 95% through-hole AXH010A0FZ cc109104898 option suffix remote sense 3 long pins: 5.08 mm 0.25 mm (0.20 in 0.010 in.) 5 rohs compliant -z

▲Up To Search▲

Price & Availability of AXH010A0FZ

	To Download AXH010A0FZ Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .